intake manifold runner control - Ford Explorer Forums
2008年11月19日 · The Intake Manifold Swirl Control used on the 2.3L Ranger consists of a manifold mounted vacuum actuator and a PCM controlled electric solenoid. The linkage from the actuator attaches to the manifold butterfly plate lever. The IMSC actuator and manifold
Intake Manifold Runner Control Stuck - Ford Explorer Forums
2005年1月16日 · Hello All, I have 2 codes thrown on my 2009 4.6 3V P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) P2007 Intake Manifold Runner Control Stuck Closed (Bank 2) I'm assuming the actuator has failed on the back of the intake plenum. I spoke with my local Ford Dealer and they want an obscene $268.00 for the actuator.
2003 Ford Ranger 16V 2.3L. P2004 error code. - Explorer Forum
2011年4月12日 · 1. Disconnected the negative cable from the battery. + - 8mm bolt on my 2003 Ford Ranger - Losen slightly, twist and pull the negative cable off. 2. Removed the 8mm bolt from the IMRC. + - The bolt was slightly rusted but I was easily able to - force the 8mm socket on and remove the bolt from the plastic - intake manifold. 3.
P2004 Intake Manifold Runner Control Issue | Ford Explorer …
2022年5月24日 · I have a 2013 Explorer Limited 3.5. I'm getting code p2004. Where is the intake manifold runner control located?
intake manifold runner control | Ford Explorer Forums - Serious ...
2022年5月28日 · Performance Upgrades - Maintenance - Modifications - Problem Solving - Off-Road - Street Trucks. Covering the Explorer, ST, Sport, Lincoln Aviator, Sport Trac, Mercury Mountaineer, Mazda Navajo, Ford Ranger, Mazda Pickups, and the Aerostar.
VIS Conversion | Ford Explorer Forums - Serious Explorations
2009年5月26日 · The 1997 and 1998 Explorer with the SOHC V6 came with a variable intake system (VIS) - also known as intake manifold runner control (IMRC). It was also available on some years of the Mustang with the DOHC V8 engine. I have found minimal documentation on the operation and performance of VIS.
IMRC Error Code, where is this part located at?? - Explorer Forum
2013年7月8日 · Basically another version of an IMRC, it should be between both heads at the rear of the engine, bolted to the intake. I haven't actually seen it for sure, but that's where it should be. It ought to have 2 rods connected to it, one on top and one bottom.
Intake manifold keeps leaking - Ford Explorer Forums
2009年10月26日 · I would suggest pulling the upper intake manifold off and checking the flatness of the mounting surface and that of the fuel rail. The fuel rail is removable by unscrewing the studs sticking up. Check that the fuel rail has a flat mounting surface on both sides and that it has a good gasket between it and the lower intake manifold.
V8 Intake Manifold Swap - Ford Explorer Forums
2018年6月26日 · I got around to swapping the intake manifold - putting the 2009 OE manifold (#9L2Z-9424-F) onto my 2006 engine (replacing the old #6L2Z-9424-FA) on the weekend. Bolts up fine, easy swap, no issues. The newer manifold requires shorter bolts (qty. 10) than the ones from the 2006 which are about 63 mm. long.
Unusual SOHC V6 upper intake manifold - Ford Explorer Forums
2009年5月26日 · FORD 4.0 SOHC ENGINE INTAKE MANIFOLD W/TB #4110 Below is the photo for the listed item. My Helpful Threads , 2000 Sport Registry (227 rwhp) 2003 Centennial Registry Join the Elite Explorers for $20 each year or try it out for $5 a month.