How to Reinforce Ceiling Joists to Handle Heavy Loads
In addition, I would add another 2x6 under the existing 2x6 and use adhesive to sister onto the 2x12 but also under the existing 2x6. In this situation, I would use double 2x joist hangers at each end of the joists. You will need to shim under the double …
Deck Joist Span Chart - Fine Homebuilding
Decks get wet and may be framed with incised treated lumber so spans may have to be adjusted. Until a few years ago, the IRC didn’t have deck joist span tables. But the 2015 IRC included a new one (Table R507.5) that will make it easy for deck builders to spec a joist size for a given span and joist spacing.
How to Calculate Deck Cantilevers - Fine Homebuilding
Needless to say, there’s a lot more to joists than simply choosing the right lumber. But that’s still the best place to start. Dried lumber makes building easier. Most decks are framed with pressure-treated dimensional lumber. The pressure-treating process leaves lumber wet; the moisture content may exceed 50%.
Thermally Broken Studs - Fine Homebuilding
For a more in-depth look at the practicality and economics of Tstuds vs. conventional framing lumber, read my companion article, “First Look at Tstuds“, at GreenBuildingAdvisor.com. —Peter Yost, technical director at Green Building Advisor. From Fine Homebuilding #286. More about Tstuds and thermal bridging. BareNaked Tstud; T-Stud Field ...
How Far Can a Deck Beam Span? - Fine Homebuilding
Deck builders can now refer to Section R507.6 Deck Beams and Table R507.6 Deck Beam Span Lengths to determine the size of 2-ply and 3-ply built-up beams made from 2×6 through 2×12 lumber. These values didn’t change in the 2018 version of the IRC. (For more on other aspects of framing an elevated deck, have a look at this guide.)
The Right Header for Every Wall - Fine Homebuilding
Engineered-lumber manufacturers provide header-span tables similar to the ones listed in the IRC, making it easy to size them. I’ve used engineered lumber as single-ply headers, multi-ply headers, and rim-board headers. In many cases, the engineered-lumber members can span greater distances compared to sawn-lumber headers of similar sizes.
doubled 2x6 joist span - Fine Homebuilding
2005年12月12日 · Ditto, with a properly sized beam down the middle doubled 2X6's should be fine. However , instead of sistering and worrying about properly connecting, they seem to still be adequate @ 8" o.c. (HF #2), basically dropping one in between, given 3/4" glued & …
Drying Wet Framing Lumber - Fine Homebuilding
There are 4 tools you can use to dry your wet framing lumber. Time, Air movement, De-humidification, and Heat. 1. Time. Given enough time (assuming it’s not getting wet again) that wet lumber will naturally dry. If the outdoor temps are above 60 degrees F then it won’t take much time. Maybe 3-5 weeks to get from 18% down to 14%.
Laminated PT 2X6's for deck posts - Fine Homebuilding
2006年3月30日 · Laminated PT 2X6’s for deck posts johnnyd | Posted in Construction Techniques on March 30, 2006 06:01am Alot of pole barn builders (ala Morton) use laminated 2X6 treated lumber instead of whole 6X6 posts for thier vertical members, and then “finger joint” regular construction grade 2X6’s for the above-grade portion.
Dimensional shrinkage of pressure treated lumber.
2019年12月3日 · I’m building a deck to an existing elevation using 2 x 8 pressure treated lumber. It measures 7 1/2″ and the wood has a moisture content that ranges anywhere from 30% to 50% on these new boards with an average rating of near 35%. The small town home center said that the lumber was kiln dried before treatment.